CDI-910 Power Supply Question

If you encounter any problems with your CD-i system or have difficulty operating some software for CD-i then post your problems here. With help from the CD-i community and the vast resources hosted on the CDinteractive network we should be able to solve any trouble your experiencing.
Post Reply
WillowFox
Burn:Cycle Activated
Posts: 10
Joined: Thu Jan 28, 2010 4:26 am
Location: USA
Contact:

CDI-910 Power Supply Question

Post by WillowFox » Tue Feb 13, 2018 3:22 am

Is 220-230 degrees Fahrenheit too hot for the mosfet to run in the CDI-910?
Also, I am installing an HDMI conversion board, after I clean up some circuitry inside, and mount the battery housing to the memory so it is not loose in here like it is now.
My clock IC snapped in half, the crystal and battery potting came off, so I was able to tack off of each side of the IC with wires connected to a crystal and a battery housing. I am using a 2330 battery, is that too much or should it be fine? I figured a 3v mainboard battery should be okay, but not sure if the battery capacity is overkill or should I even worry about it?
Screenshot_20180212-205127.jpg
CDi-910 Thermal (2 days idle) in Fahrenheit
Screenshot_20180212-205127.jpg (115.68 KiB) Viewed 22472 times
Screenshot_20180212-205127.jpg
CDi-910 Thermal (2 days idle) in Fahrenheit
Screenshot_20180212-205127.jpg (115.68 KiB) Viewed 22472 times
Attachments
Screenshot_20180212-205319.jpg
Close up of CDi-910 power supply thermal
Screenshot_20180212-205319.jpg (96.77 KiB) Viewed 22471 times

User avatar
Shikotei
Burn:Cycle Activated
Posts: 42
Joined: Mon Mar 01, 2010 5:01 pm
Location: Netherlands
Contact:

Re: CDI-910 Power Supply Question

Post by Shikotei » Fri Feb 23, 2018 8:32 pm

I haven't ever measured temperatures of the CD-i consoles, but know they don't exactly stay frosty.
I'd assume temperatures around the power supply to be somewhat near 50-70 Celsius as 'acceptable' during operation.

But as a techie I'm worried. Not many devices are built to operate at high temperatures, even old stuff. I remember my laptop (heavy duty from 2010 to 2017) getting fried at 90-100 C (long after the thermal security (used to trigger at 70 C) broke because it overheated before).

Do you know the idle temperatures of your CD-i before you added the HDMI converter? Perhaps the added power requirement causes the console to operate beyond specs?

C to F:
50 = 122
60 = 140
70 = 158
80 = 176
90 = 194
100 = 212
110 = 230

WillowFox
Burn:Cycle Activated
Posts: 10
Joined: Thu Jan 28, 2010 4:26 am
Location: USA
Contact:

Re: CDI-910 Power Supply Question

Post by WillowFox » Thu Mar 01, 2018 2:08 am

This is actually before any modifications other than the save chip battery added.
I think that mosfet is running a little hot, but not way out of scope.
I may put a fan in the unit and redo the heatsync compound on the mosfet, or even put a set of cooling fins on there as well, instead of that flimsy metal heat wick they have, that is little more than a shard of metal.

User avatar
Adr990
Burn:Cycle Activated
Posts: 24
Joined: Mon Jul 05, 2010 10:42 am
Location: The Netherlands

Re: CDI-910 Power Supply Question

Post by Adr990 » Mon Jan 28, 2019 1:01 am

It should be easy enough to create your own power supply, making it smaller and more efficient than what was put together back then.
I have been meaning to do so, I just need to get some components in to get started with a smaller replacement PSU.


But, I am mighty curious, are you installing a regular composite/rgb/s-video/scart to HDMI converter into a CD-i case, soldering it on directly?
Or is there an actual mod/fpga board that hooks onto the video chip, like they have for a couple of retro consoles nowadays?
I fix Timekeepers and noisy/faulty disc trays/readers.
Looking for a complete games list of the CD-i. :lol:

Post Reply